Expert Answers about Bimini Top Parts
- Do the Taylor Made Bimini Top Aluminum Slide Assemblies Have Locks in the Track
- There are not track locks on the Taylor Made Bimini Top Aluminum Slide Assemblies # 369993030. There are endcaps that cover the ends of each track to keep the sliders from falling out but no progressive locks in the track to keep it from shifting back and forth when the top is up and underway.
view full answer... - How Do Taylor Made Internal Eye Ends for 3/4" Bimini Top Poles Connect to Poles
- The grooved ends of the Taylor Made Internal Eye Ends for 3/4" Bimini Top Poles # TM88YR will "snap" into place (for lack of a better term) on the poles. If you check out the end of your pole that this fits to you'll see what I'm talking about.
view full answer... - Can Damaged Internal Eye Ends Be Removed From Bimini Top Poles
- Removing the damaged internal eye ends is going to be very tricky. There really is not a great way to remove them, especially if they are crimped in to the poles. One option is to cut the pole, but this can throw off how it fits. Your best bet would be to cut off the damaged eye flush with the end of the pole, and use an external eye like part # 36911729. This way you can have a new eye end, and you will not have to shorten the pole.
view full answer... - Installing a Sailcloth Replace-a-top on a 2008 Jeep Wrangler
- You are basically doing a reverse of step 7 in the instructions, linked for reference, to install the new top. And after that it is pretty much reversing steps 1 through 6 (removing the old top). Sometimes the new top will not easily stay in place to screw it down. It helps to have an extra set of hands to hold it in place so you can wedge it in properly to screw it down and secure it. If no one is available to help then you can use masking tape (but nothing stronger than that because it...
view full answer... - Do T-tops Need to Be Removed on a 2007 Jeep Wrangler to Install a Bestop Windshield Channel #B51243
- You will have to remove the T-tops of your 2007 Jeep Wrangler to install the Bestop No-drill Windshield Channel # B51243.
If you want to reinstall your T-tops you will have to remove the # B51243 and whichever bikini top you choose as this part installs on the portion of your roof that is accessible when the T-tops are off.
I attached installation instructions for you to check out also.
view full answer... - How Does the Rear Hanger Get Welded to the Trailer Frame
- On the Redline Rear Hanger, part # 30-20, which is the rear hanger included with kit # APS1, it is welded to the trailer with the side marked top, facing the outside of the trailer with the word top showing. So the U-shape part is what gets welded to the frame, on the flat part.
I included a picture of the hangar that shows the top marking and how it is positioned on the trailer.
view full answer... - Difference in Side Wind Operated A-Frame Jack and Top Wind A-Frame Jack
- The choice between a side wind jack like the etrailer Round, A-Frame Jack - Sidewind, part # TJA-5000S-B, and a top wind jack like the Bulldog Round, A-Frame Jack - Topwind, part # BD155032, will usually be for clearance issues. A top wind jack will be used when there is something on the trailer that will interfere with the rotation of the side wind handle on the jack and a side wind jack would be used if there is interference for the top wind jack handle.
If the clearance issues are not...
view full answer... - How To Mount the Rhino-Rack Sunseeker Awning On a Roof with Cargo Basket
- The Rhino-Rack Sunseeker Awning part # RR32133 can be attached one of two ways. The first way would be to attach inside the channels on a Rhino-Rack Pioneer Platform Rack. The second way would be to attach inside the channels on a set of crossbars with top channels. If you have flush crossbars with top channels, then you could use part # RR32123 or part # RR32127 but those are your only options.
The Rhino-Rack Sunseeker Awning will not mount direct to a cargo basket but so long as your...
view full answer... - 4-Way Round Chrome Car End Wiring Details
- There is not an industry standard wiring diagram for the 4-Way Round Car End, part # PK11410. You will need to use a circuit tester, part # PTW2993, to check which pins have which functions on your trailer, and then attach the corresponding wires to their respective pins on the vehicle connector.
If you are towing a vehicle behind a motor home the connections are usually as follows. The top left connection inside the vehicle end, with the cover raised, is the yellow left turn/brake connector,...
view full answer... - Replacing Glass Top for Furrion 2-in-1 Range Oven
- Replacing the Glass Top # C-FSRE21SA-SS-003 on your Furrion 2-in-1 Range Oven is a really simple process.
I even reached out to my contact at Furrion just to make sure there aren't any unforeseen difficulties with this particular part and he actually said the glass top is probably the easiest component on this oven to swap out. It will literally be just a matter of vertically lifting up on the existing glass top to release the spring so it can be removed (if your current glass is broken...
view full answer... - How Hard is it to Remove the Top Part of the Jack-It Trailer Mount Bike Rack Carrier
- The part the Jack-It # LC429756 that holds the bike rack part is held to the base assembly with one bolt. The bike rack itself is also held in with a bolt. So either way, whether you want to take off the whole top assembly or just he bike rack part, you are removing one bolt so it will be very easy to do. I have included a picture pointing out the 2 bolts I mentioned.
view full answer... - How to Remove and Install the Top Mounting Clamp for Thule Ride-On Adapter
- There will be 3 combinations of nuts and bolts that secure the Replacement Top Mounting Clamp for Thule Ride-On Adapter # 853-5267. Remove the nuts, then the bolts from your accessories and then simply reverse that process to install the replacement part.
view full answer... - How Much Space is Required Between the Top of a Stove and the Bottom of the Furrion Microwave
- It looks like there are a couple of regulations depending on area, but most have a range of 13" - 18" between the bottom of the microwave and the top of your stove.
For the Furrion Over the Range RV Convection Microwave, part # FMCM15SS, Furrion states that the top of the microwave be mounted at least 30" above the top of the stove. Since this unit is 15" tall, that means the bottom needs to be 15" above the stove top.
I've linked to a video review of this unit for you to look at.
view full answer... - Installation of Bestop Trektop Soft Top # B5685335 on 2008 Jeep Wrangler Unlimited
- The Bestop Trektop Soft Top, part # B5685335, will fit your 2008 Jeep Wrangler Unlimited and comes with all of the hardware that is needed for installation. The header is included with the soft top.
The top attaches directly to the Wrangler Unlimited factory hardware with no need of a bow support system. The rear window will attach to the included tailgate retainer that clips onto the rear tailgate. The quarter windows on the side will use plastic retainer strips that slip along the bottom...
view full answer... - Does Top of Rail Mate Folding Hand Rail Attach to the Side of the RV
- The top of the Rail Mate folding handrail # AP-101 is not attached to anything. The mounting brackets that hold the rail are only attached to the steps because the hand rail part is meant to be removable and the brackets are not.
view full answer... - Is Frame Adapter Needed to Carry Womans Bike with Hollywood Racks Over the Top
- To carry a woman's style bike that does not have a horizontal top tube with the Hollywood Racks Over the Top part # HRF2 you will need a bike frame adapter. The best option is the part # UB01 as we've found it's the easiest to use, has the widest range, and is priced great.
I attached a review video for the adapter and bike rack for you to check out as well.
view full answer... - Can the Top Mounting Bracket on Stromberg-Carlson Scissor Jack # JSC-24-IND Be Rotated
- The top bracket on Stromberg-Carlson Scissor Jack # JSC-24-IND that mounts to your trailer frame or other structural point cannot be repositioned. It can only be mounted as intended, 90-degrees from the main assembly. This part can be removed but the jack cannot be used without it.
view full answer... - Is There a Tool Needed to Install Rubber Top Lip Wiper Seal for RV Slide Out - Press On
- I do have an option for you but there isn't really a specific tool needed for the Rubber Top Lip Wiper Seal for RV Slide Out part # SR23VR. It features a simple press-on installation so there will be no tool needed for this. That said, I could see how removal would be a bit more challenging, if you just simply pulled up on the top of the seal you would likely tear it so it might help to use a pry tool and lift up at the bottom of the seal where it's pressed onto the flange. In which case,...
view full answer... - Do All Windows Zip Out on Bestop Replace-A-Top B5136215
- The Bestop Replace-A-Top # B5136215 has a zip out rear window, however the sides do not zip out. All the windows are vinyl but only the rear is removable; the sides are attached to the frame or main piece of the top.
If you looking for a top that will keep you covered but still have the open air in the back you should check out Bestop Strapless Bikini # B5257015. This top has a canopy over the cab to keep you and the passengers dry and protected, but the back is open and doesn't have any...
view full answer... - Does the Rear Seal for the TruXedo Lo Pro Soft Roll-up Tonneau Cover Sit On Top of the Tailgate
- The seal for the TruXedo Lo Pro Soft Roll-up Tonneau Covers like part # TX520601 should rest on top of the tailgate as that is how it's able to keep out water.
view full answer...
Go To Results